DTF Transfer

YOU WILL RECEIVE TONS OF COMPLIMENTS: Prepare for a flood of compliments! Each design is a fantastic conversation starter, and everyone will be curious about where you got it. Print Size:  Pressing Instructions:  Pre-Press: Removing moisture is unnecessary but recommended. Only do a prepress if you so desire. Position Your Design: Take your time to line up your transfer in the desired location on your item. Normally, there is no need to use heat-resistant tape on flat heat presses to keep your design in place, however it is highly recommended when pressing transfers onto hats or when using an iron to keep the transfer in place. You’ll get a feel for when this is needed. Press 1: Place a Parchment paper on top of the design & Press your transfer with Med to Heavy pressure at 310°F / 155°C for 30-35seconds. You cannot damage the transfer by pressing with more heat, pressure, or time — within reason. However, too much heat can damage your garment, so test first and use parchment paper or a protective guard sheet to protect your garment from a direct iron. Press 2: Let  Sit for 10 Seconds and Repeat press Let It Cool. Then Peel It: After pressing, let your transfer rest until it is cool to the touch (minimum of 15-30 seconds). Once cool, lift the transfer from one corner and gently peel back. Don’t use your hands, use your EYES. This ensures every piece of your design is adhering to your item. If not, stop peeling, lay it back down, and trouble shoot as follows — (1.) If some or all of the design does not transfer AND it was cool when peeling, it means there was not enough heat, pressure, or time. Press your transfer again with more pressure and time first (+5-10 seconds). (2.) If that doesn’t work, try 15°F heat increments until you find the sweet spot. You truly cannot damage the transfer by pressing multiple times. Final Press & Wash Instructions: Place a parchment paper or a single layer of t-shirt material over the design and press again for 15 seconds to soften the design, increase durability, and remove shine. If you want a shiny finish, cover with a protective guard sheet for the final press. When washing, flip shirt inside out, wash on cold and dry using low heat or hang. *By purchasing you agree that the process for the application of our transfers is your responsibility and we not refund due to user error. There is a learning curve to heat pressing and transfers and every heat press is different.**A heat press is recommended though this will work with a circut or an iron as well***All Sales are Final

YOU WILL RECEIVE TONS OF COMPLIMENTS: Prepare for a flood of compliments! Each design is a fantastic conversation starter, and everyone will be curious about where you got it. Print Size:  Pressing Instructions:  Pre-Press: Removing moisture is unnecessary but recommended. Only do a prepress if you so desire. Position Your Design: Take your time to line up your transfer in the desired location on your item. Normally, there is no need to use heat-resistant tape on flat heat presses to keep your design in place, however it is highly recommended when pressing transfers onto hats or when using an iron to keep the transfer in place. You’ll get a feel for when this is needed. Press 1: Place a Parchment paper on top of the design & Press your transfer with Med to Heavy pressure at 310°F / 155°C for 30-35seconds. You cannot damage the transfer by pressing with more heat, pressure, or time — within reason. However, too much heat can damage your garment, so test first and use parchment paper or a protective guard sheet to protect your garment from a direct iron. Press 2: Let  Sit for 10 Seconds and Repeat press Let It Cool. Then Peel It: After pressing, let your transfer rest until it is cool to the touch (minimum of 15-30 seconds). Once cool, lift the transfer from one corner and gently peel back. Don’t use your hands, use your EYES. This ensures every piece of your design is adhering to your item. If not, stop peeling, lay it back down, and trouble shoot as follows — (1.) If some or all of the design does not transfer AND it was cool when peeling, it means there was not enough heat, pressure, or time. Press your transfer again with more pressure and time first (+5-10 seconds). (2.) If that doesn’t work, try 15°F heat increments until you find the sweet spot. You truly cannot damage the transfer by pressing multiple times. Final Press & Wash Instructions: Place a parchment paper or a single layer of t-shirt material over the design and press again for 15 seconds to soften the design, increase durability, and remove shine. If you want a shiny finish, cover with a protective guard sheet for the final press. When washing, flip shirt inside out, wash on cold and dry using low heat or hang. *By purchasing you agree that the process for the application of our transfers is your responsibility and we not refund due to user error. There is a learning curve to heat pressing and transfers and every heat press is different.**A heat press is recommended though this will work with a circut or an iron as well***All Sales are Final

YOU WILL RECEIVE TONS OF COMPLIMENTS: Prepare for a flood of compliments! Each design is a fantastic conversation starter, and everyone will be curious about where you got it. Print Size:  Pressing Instructions:  Pre-Press: Removing moisture is unnecessary but recommended. Only do a prepress if you so desire. Position Your Design: Take your time to line up your transfer in the desired location on your item. Normally, there is no need to use heat-resistant tape on flat heat presses to keep your design in place, however it is highly recommended when pressing transfers onto hats or when using an iron to keep the transfer in place. You’ll get a feel for when this is needed. Press 1: Place a Parchment paper on top of the design & Press your transfer with Med to Heavy pressure at 310°F / 155°C for 30-35seconds. You cannot damage the transfer by pressing with more heat, pressure, or time — within reason. However, too much heat can damage your garment, so test first and use parchment paper or a protective guard sheet to protect your garment from a direct iron. Press 2: Let  Sit for 10 Seconds and Repeat press Let It Cool. Then Peel It: After pressing, let your transfer rest until it is cool to the touch (minimum of 15-30 seconds). Once cool, lift the transfer from one corner and gently peel back. Don’t use your hands, use your EYES. This ensures every piece of your design is adhering to your item. If not, stop peeling, lay it back down, and trouble shoot as follows — (1.) If some or all of the design does not transfer AND it was cool when peeling, it means there was not enough heat, pressure, or time. Press your transfer again with more pressure and time first (+5-10 seconds). (2.) If that doesn’t work, try 15°F heat increments until you find the sweet spot. You truly cannot damage the transfer by pressing multiple times. Final Press & Wash Instructions: Place a parchment paper or a single layer of t-shirt material over the design and press again for 15 seconds to soften the design, increase durability, and remove shine. If you want a shiny finish, cover with a protective guard sheet for the final press. When washing, flip shirt inside out, wash on cold and dry using low heat or hang. *By purchasing you agree that the process for the application of our transfers is your responsibility and we not refund due to user error. There is a learning curve to heat pressing and transfers and every heat press is different.**A heat press is recommended though this will work with a circut or an iron as well***All Sales are Final

YOU WILL RECEIVE TONS OF COMPLIMENTS: Prepare for a flood of compliments! Each design is a fantastic conversation starter, and everyone will be curious about where you got it.Print Size: 9.5 inches or 241 mm WidthWhat You’ll Need: DTF Hot Peel Transfer A household iron or heat press machine A flat, heat-resistant surface (e.g., an ironing board or countertop) Garment (cotton, polyester, or blends) Parchment paper or baking paper Pressing Instructions: Prep Your Garment: Lay the garment flat and smooth out wrinkles. Preheat with your iron or heat press for 5 seconds to remove moisture. Position the Transfer:Place the transfer face down where you want the design. Apply Heat: Using an Iron: Press firmly and move in circles for 30-40 seconds. Using a Heat Press: Set to 310-325°F and press for 10-15 seconds. Peel the Film:Carefully peel off the film while it’s still hot. Seal the Design (Optional):Cover with parchment paper and press again for 5 seconds for extra durability. Wash Care: Wait 24 hours before washing. Wash inside out in cold water and avoid bleach or high heat. By purchasing you agree that the process for the application of our transfers is your responsibility and we not refund due to user error. There is a learning curve to heat pressing and transfers and every heat press is different.**A heat press is recommended though this will work with a circut or an iron as well***All Sales are Final

Show your true colors with our Can't Fix Stupid Unisex T-Shirts!The Can't Fix Stupid Unisex T-shirt is your go-to shirt for a witty, no-nonsense take on life. Crafted for supreme comfort and straightforward humor, this unisex tee features a bold and relatable slogan that's sure to get a knowing nod or a good laugh. Whether you're dealing with everyday frustrations, enjoying a casual get-together, or just appreciate a clever statement, this tee keeps you stylish and unapologetically real. Ultra-soft, durable, and made to move with you—this is honest humor in fabric form.🎁 A Perfect Gift for the Witty FriendLooking for a gift that speaks directly to their sense of humor? This Can't Fix Stupid Unisex T-shirt is ideal for coworkers, family members, or anyone who appreciates a sarcastic and hilarious take on the world. A thoughtful and bold gift for birthdays, holidays, or any day you want to share a good laugh.Why You’ll Love Our Can't Fix Stupid Unisex T-shirt:✅ Relatable and humorous slogan✅ Ultra-comfortable and soft feel✅ Unisex fit for everyday comfort✅ Statement-making style that's a conversation starterProduct Features:Ultra-Soft Ring-Spun Cotton – Crafted from 100% ring-spun cotton (30 singles) for a soft, smooth feel and enhanced comfort.Lightweight & Versatile – 4.5 oz./yd² (US) / 7.5 oz./L yd (CA) fabric weight makes it perfect for everyday wear, layering, or custom printing.Color-Specific Fabric Blends – Antique Colors & Sport Grey: 90% cotton / 10% polyester, Dark Heather & Heather Colors: 65% polyester / 35% cotton, Graphite Heather: 50% cotton / 50% polyester.Smooth Print Surface – Softstyle fabric offers a smooth, stable surface ideal for screen printing, DTG, or heat transfers.Modern Classic Fit – Features a flattering modern fit with a narrow rib collar for a clean, contemporary look.Enhanced Durability & Comfort – Includes taped neck and shoulders for added comfort and long-lasting wear.Tear-Away Label – Tear-away tag allows for easy rebranding or itch-free wear.Sustainably Made – Produced using OEKO-TEX® certified low-impact dyes and in partnership with Better Cotton to support sustainable cotton farming globally.Stand tall. Wear proud. Add the Can't Fix Stupid Unisex T-shirt to your collection today and let the world know you've got a great sense of humor!Size & Care Instructions:📏 Size Chart Available – Check our sizing guide to find the perfect fit.🧼 Care Instructions: Machine wash cold, tumble dry low, and iron inside out for long-lasting wear.

YOU WILL RECEIVE TONS OF COMPLIMENTS: Prepare for a flood of compliments! Each design is a fantastic conversation starter, and everyone will be curious about where you got it. Print Size: 9.5 inches or 241 mm Width What You’ll Need: DTF Hot Peel Transfer A household iron or heat press machine A flat, heat-resistant surface (e.g., an ironing board or countertop) Garment (cotton, polyester, or blends) Parchment paper or baking paper Pressing Instructions: 1. Prep Your Garment: Lay the garment flat and smooth out wrinkles. Preheat with your iron or heat press for 5 seconds to remove moisture. Position the Transfer: Place the transfer face down where you want the design. 2. Apply Heat: Using an Iron: Press firmly and move in circles for 30-40 seconds. Using a Heat Press: Set to 310-325°F and press for 10-15 seconds. Peel the Film: Carefully peel off the film while it’s still hot. Seal the Design (Optional): Cover with parchment paper and press again for 5 seconds for extra durability. 3. Wash Care: Wait 24 hours before washing. Wash inside out in cold water and avoid bleach or high heat. By purchasing you agree that the process for the application of our transfers is your responsibility and we not refund due to user error. There is a learning curve to heat pressing and transfers and every heat press is different. **A heat press is recommended though this will work with a circut or an iron as well ***All Sales are Final

YOU WILL RECEIVE TONS OF COMPLIMENTS: Prepare for a flood of compliments! Each design is a fantastic conversation starter, and everyone will be curious about where you got it. Print Size: 9.5 inches or 241 mm Width What You’ll Need: DTF Hot Peel Transfer A household iron or heat press machine A flat, heat-resistant surface (e.g., an ironing board or countertop) Garment (cotton, polyester, or blends) Parchment paper or baking paper Pressing Instructions: 1. Prep Your Garment: Lay the garment flat and smooth out wrinkles. Preheat with your iron or heat press for 5 seconds to remove moisture. Position the Transfer:Place the transfer face down where you want the design. 2. Apply Heat: Using an Iron: Press firmly and move in circles for 30-40 seconds. Using a Heat Press: Set to 310-325°F and press for 10-15 seconds. Peel the Film:Carefully peel off the film while it’s still hot. Seal the Design (Optional):Cover with parchment paper and press again for 5 seconds for extra durability. 3. Wash Care: Wait 24 hours before washing. Wash inside out in cold water and avoid bleach or high heat. By purchasing you agree that the process for the application of our transfers is your responsibility and we not refund due to user error. There is a learning curve to heat pressing and transfers and every heat press is different. **A heat press is recommended though this will work with a circut or an iron as well ***All Sales are Final

YOU WILL RECEIVE TONS OF COMPLIMENTS: Prepare for a flood of compliments! Each design is a fantastic conversation starter, and everyone will be curious about where you got it. Print Size: 9.5 inches or 241 mm Width What You’ll Need: DTF Hot Peel Transfer A household iron or heat press machine A flat, heat-resistant surface (e.g., an ironing board or countertop) Garment (cotton, polyester, or blends) Parchment paper or baking paper Pressing Instructions: 1. Prep Your Garment: Lay the garment flat and smooth out wrinkles. Preheat with your iron or heat press for 5 seconds to remove moisture. Position the Transfer:Place the transfer face down where you want the design. 2. Apply Heat: Using an Iron: Press firmly and move in circles for 30-40 seconds. Using a Heat Press: Set to 310-325°F and press for 10-15 seconds. Peel the Film:Carefully peel off the film while it’s still hot. Seal the Design (Optional):Cover with parchment paper and press again for 5 seconds for extra durability. 3. Wash Care: Wait 24 hours before washing. Wash inside out in cold water and avoid bleach or high heat. By purchasing you agree that the process for the application of our transfers is your responsibility and we not refund due to user error. There is a learning curve to heat pressing and transfers and every heat press is different. **A heat press is recommended though this will work with a circut or an iron as well ***All Sales are Final

YOU WILL RECEIVE TONS OF COMPLIMENTS: Prepare for a flood of compliments! Each design is a fantastic conversation starter, and everyone will be curious about where you got it. Print Size: 9.5 inches or 241 mm Width What You’ll Need: DTF Hot Peel Transfer A household iron or heat press machine A flat, heat-resistant surface (e.g., an ironing board or countertop) Garment (cotton, polyester, or blends) Parchment paper or baking paper Pressing Instructions: 1. Prep Your Garment: Lay the garment flat and smooth out wrinkles. Preheat with your iron or heat press for 5 seconds to remove moisture. Position the Transfer:Place the transfer face down where you want the design. 2. Apply Heat: Using an Iron: Press firmly and move in circles for 30-40 seconds. Using a Heat Press: Set to 310-325°F and press for 10-15 seconds. Peel the Film:Carefully peel off the film while it’s still hot. Seal the Design (Optional):Cover with parchment paper and press again for 5 seconds for extra durability. 3. Wash Care: Wait 24 hours before washing. Wash inside out in cold water and avoid bleach or high heat. By purchasing you agree that the process for the application of our transfers is your responsibility and we not refund due to user error. There is a learning curve to heat pressing and transfers and every heat press is different. **A heat press is recommended though this will work with a circut or an iron as well ***All Sales are Final

YOU WILL RECEIVE TONS OF COMPLIMENTS: Prepare for a flood of compliments! Each design is a fantastic conversation starter, and everyone will be curious about where you got it. Print Size: 9.5 inches or 241 mm Width What You’ll Need: DTF Hot Peel Transfer A household iron or heat press machine A flat, heat-resistant surface (e.g., an ironing board or countertop) Garment (cotton, polyester, or blends) Parchment paper or baking paper Pressing Instructions: 1. Prep Your Garment: Lay the garment flat and smooth out wrinkles. Preheat with your iron or heat press for 5 seconds to remove moisture. Position the Transfer:Place the transfer face down where you want the design. 2. Apply Heat: Using an Iron: Press firmly and move in circles for 30-40 seconds. Using a Heat Press: Set to 310-325°F and press for 10-15 seconds. Peel the Film:Carefully peel off the film while it’s still hot. Seal the Design (Optional):Cover with parchment paper and press again for 5 seconds for extra durability. 3. Wash Care: Wait 24 hours before washing. Wash inside out in cold water and avoid bleach or high heat. By purchasing you agree that the process for the application of our transfers is your responsibility and we not refund due to user error. There is a learning curve to heat pressing and transfers and every heat press is different. **A heat press is recommended though this will work with a circut or an iron as well ***All Sales are Final

YOU WILL RECEIVE TONS OF COMPLIMENTS: Prepare for a flood of compliments! Each design is a fantastic conversation starter, and everyone will be curious about where you got it. Print Size: 9.5 inches or 241 mm Width What You’ll Need: DTF Hot Peel Transfer A household iron or heat press machine A flat, heat-resistant surface (e.g., an ironing board or countertop) Garment (cotton, polyester, or blends) Parchment paper or baking paper Pressing Instructions: 1. Prep Your Garment: Lay the garment flat and smooth out wrinkles. Preheat with your iron or heat press for 5 seconds to remove moisture. Position the Transfer: Place the transfer face down where you want the design. 2. Apply Heat: Using an Iron: Press firmly and move in circles for 30-40 seconds. Using a Heat Press: Set to 310-325°F and press for 10-15 seconds. Peel the Film: Carefully peel off the film while it’s still hot. Seal the Design (Optional): Cover with parchment paper and press again for 5 seconds for extra durability. 3. Wash Care: Wait 24 hours before washing. Wash inside out in cold water and avoid bleach or high heat. By purchasing you agree that the process for the application of our transfers is your responsibility and we not refund due to user error. There is a learning curve to heat pressing and transfers and every heat press is different. **A heat press is recommended though this will work with a circut or an iron as well ***All Sales are Final

YOU WILL RECEIVE TONS OF COMPLIMENTS: Prepare for a flood of compliments! Each design is a fantastic conversation starter, and everyone will be curious about where you got it.Print Size: 9.5 inches or 241 mm WidthWhat You’ll Need: DTF Hot Peel Transfer A household iron or heat press machine A flat, heat-resistant surface (e.g., an ironing board or countertop) Garment (cotton, polyester, or blends) Parchment paper or baking paper Pressing Instructions: Prep Your Garment: Lay the garment flat and smooth out wrinkles. Preheat with your iron or heat press for 5 seconds to remove moisture. Position the Transfer:Place the transfer face down where you want the design. Apply Heat: Using an Iron: Press firmly and move in circles for 30-40 seconds. Using a Heat Press: Set to 310-325°F and press for 10-15 seconds. Peel the Film:Carefully peel off the film while it’s still hot. Seal the Design (Optional):Cover with parchment paper and press again for 5 seconds for extra durability. Wash Care: Wait 24 hours before washing. Wash inside out in cold water and avoid bleach or high heat. By purchasing you agree that the process for the application of our transfers is your responsibility and we not refund due to user error. There is a learning curve to heat pressing and transfers and every heat press is different.**A heat press is recommended though this will work with a circut or an iron as well***All Sales are Final

YOU WILL RECEIVE TONS OF COMPLIMENTS: Prepare for a flood of compliments! Each design is a fantastic conversation starter, and everyone will be curious about where you got it. Print Size: Pressing Instructions:  Pre-Press: Removing moisture is unnecessary but recommended. Only do a prepress if you so desire. Position Your Design: Take your time to line up your transfer in the desired location on your item. Normally, there is no need to use heat-resistant tape on flat heat presses to keep your design in place, however it is highly recommended when pressing transfers onto hats or when using an iron to keep the transfer in place. You’ll get a feel for when this is needed. Press 1: Place a Parchment paper on top of the design & Press your transfer with Med to Heavy pressure at 310°F / 155°C for 30-35seconds. You cannot damage the transfer by pressing with more heat, pressure, or time — within reason. However, too much heat can damage your garment, so test first and use parchment paper or a protective guard sheet to protect your garment from a direct iron. Press 2: Let  Sit for 10 Seconds and Repeat press Let It Cool. Then Peel It: After pressing, let your transfer rest until it is cool to the touch (minimum of 15-30 seconds). Once cool, lift the transfer from one corner and gently peel back. Don’t use your hands, use your EYES. This ensures every piece of your design is adhering to your item. If not, stop peeling, lay it back down, and trouble shoot as follows — (1.) If some or all of the design does not transfer AND it was cool when peeling, it means there was not enough heat, pressure, or time. Press your transfer again with more pressure and time first (+5-10 seconds). (2.) If that doesn’t work, try 15°F heat increments until you find the sweet spot. You truly cannot damage the transfer by pressing multiple times. Final Press & Wash Instructions: Place a parchment paper or a single layer of t-shirt material over the design and press again for 15 seconds to soften the design, increase durability, and remove shine. If you want a shiny finish, cover with a protective guard sheet for the final press. When washing, flip shirt inside out, wash on cold and dry using low heat or hang. *By purchasing you agree that the process for the application of our transfers is your responsibility and we not refund due to user error. There is a learning curve to heat pressing and transfers and every heat press is different.**A heat press is recommended though this will work with a circut or an iron as well***All Sales are Final

YOU WILL RECEIVE TONS OF COMPLIMENTS: Prepare for a flood of compliments! Each design is a fantastic conversation starter, and everyone will be curious about where you got it. Print Size: Pressing Instructions:  Pre-Press: Removing moisture is unnecessary but recommended. Only do a prepress if you so desire. Position Your Design: Take your time to line up your transfer in the desired location on your item. Normally, there is no need to use heat-resistant tape on flat heat presses to keep your design in place, however it is highly recommended when pressing transfers onto hats or when using an iron to keep the transfer in place. You’ll get a feel for when this is needed. Press 1: Place a Parchment paper on top of the design & Press your transfer with Med to Heavy pressure at 310°F / 155°C for 30-35seconds. You cannot damage the transfer by pressing with more heat, pressure, or time — within reason. However, too much heat can damage your garment, so test first and use parchment paper or a protective guard sheet to protect your garment from a direct iron. Press 2: Let  Sit for 10 Seconds and Repeat press Let It Cool. Then Peel It: After pressing, let your transfer rest until it is cool to the touch (minimum of 15-30 seconds). Once cool, lift the transfer from one corner and gently peel back. Don’t use your hands, use your EYES. This ensures every piece of your design is adhering to your item. If not, stop peeling, lay it back down, and trouble shoot as follows — (1.) If some or all of the design does not transfer AND it was cool when peeling, it means there was not enough heat, pressure, or time. Press your transfer again with more pressure and time first (+5-10 seconds). (2.) If that doesn’t work, try 15°F heat increments until you find the sweet spot. You truly cannot damage the transfer by pressing multiple times. Final Press & Wash Instructions: Place a parchment paper or a single layer of t-shirt material over the design and press again for 15 seconds to soften the design, increase durability, and remove shine. If you want a shiny finish, cover with a protective guard sheet for the final press. When washing, flip shirt inside out, wash on cold and dry using low heat or hang. *By purchasing you agree that the process for the application of our transfers is your responsibility and we not refund due to user error. There is a learning curve to heat pressing and transfers and every heat press is different.**A heat press is recommended though this will work with a circut or an iron as well***All Sales are Final

YOU WILL RECEIVE TONS OF COMPLIMENTS: Prepare for a flood of compliments! Each design is a fantastic conversation starter, and everyone will be curious about where you got it. Print Size: Pressing Instructions:  Pre-Press: Removing moisture is unnecessary but recommended. Only do a prepress if you so desire. Position Your Design: Take your time to line up your transfer in the desired location on your item. Normally, there is no need to use heat-resistant tape on flat heat presses to keep your design in place, however it is highly recommended when pressing transfers onto hats or when using an iron to keep the transfer in place. You’ll get a feel for when this is needed. Press 1: Place a Parchment paper on top of the design & Press your transfer with Med to Heavy pressure at 310°F / 155°C for 30-35seconds. You cannot damage the transfer by pressing with more heat, pressure, or time — within reason. However, too much heat can damage your garment, so test first and use parchment paper or a protective guard sheet to protect your garment from a direct iron. Press 2: Let  Sit for 10 Seconds and Repeat press Let It Cool. Then Peel It: After pressing, let your transfer rest until it is cool to the touch (minimum of 15-30 seconds). Once cool, lift the transfer from one corner and gently peel back. Don’t use your hands, use your EYES. This ensures every piece of your design is adhering to your item. If not, stop peeling, lay it back down, and trouble shoot as follows — (1.) If some or all of the design does not transfer AND it was cool when peeling, it means there was not enough heat, pressure, or time. Press your transfer again with more pressure and time first (+5-10 seconds). (2.) If that doesn’t work, try 15°F heat increments until you find the sweet spot. You truly cannot damage the transfer by pressing multiple times. Final Press & Wash Instructions: Place a parchment paper or a single layer of t-shirt material over the design and press again for 15 seconds to soften the design, increase durability, and remove shine. If you want a shiny finish, cover with a protective guard sheet for the final press. When washing, flip shirt inside out, wash on cold and dry using low heat or hang. *By purchasing you agree that the process for the application of our transfers is your responsibility and we not refund due to user error. There is a learning curve to heat pressing and transfers and every heat press is different.**A heat press is recommended though this will work with a circut or an iron as well***All Sales are Final

YOU WILL RECEIVE TONS OF COMPLIMENTS: Prepare for a flood of compliments! Each design is a fantastic conversation starter, and everyone will be curious about where you got it. Print Size: Pressing Instructions:  Pre-Press: Removing moisture is unnecessary but recommended. Only do a prepress if you so desire. Position Your Design: Take your time to line up your transfer in the desired location on your item. Normally, there is no need to use heat-resistant tape on flat heat presses to keep your design in place, however it is highly recommended when pressing transfers onto hats or when using an iron to keep the transfer in place. You’ll get a feel for when this is needed. Press 1: Place a Parchment paper on top of the design & Press your transfer with Med to Heavy pressure at 310°F / 155°C for 30-35seconds. You cannot damage the transfer by pressing with more heat, pressure, or time — within reason. However, too much heat can damage your garment, so test first and use parchment paper or a protective guard sheet to protect your garment from a direct iron. Press 2: Let  Sit for 10 Seconds and Repeat press Let It Cool. Then Peel It: After pressing, let your transfer rest until it is cool to the touch (minimum of 15-30 seconds). Once cool, lift the transfer from one corner and gently peel back. Don’t use your hands, use your EYES. This ensures every piece of your design is adhering to your item. If not, stop peeling, lay it back down, and trouble shoot as follows — (1.) If some or all of the design does not transfer AND it was cool when peeling, it means there was not enough heat, pressure, or time. Press your transfer again with more pressure and time first (+5-10 seconds). (2.) If that doesn’t work, try 15°F heat increments until you find the sweet spot. You truly cannot damage the transfer by pressing multiple times. Final Press & Wash Instructions: Place a parchment paper or a single layer of t-shirt material over the design and press again for 15 seconds to soften the design, increase durability, and remove shine. If you want a shiny finish, cover with a protective guard sheet for the final press. When washing, flip shirt inside out, wash on cold and dry using low heat or hang. *By purchasing you agree that the process for the application of our transfers is your responsibility and we not refund due to user error. There is a learning curve to heat pressing and transfers and every heat press is different.**A heat press is recommended though this will work with a circut or an iron as well***All Sales are Final

YOU WILL RECEIVE TONS OF COMPLIMENTS: Prepare for a flood of compliments! Each design is a fantastic conversation starter, and everyone will be curious about where you got it. Print Size: Pressing Instructions:  Pre-Press: Removing moisture is unnecessary but recommended. Only do a prepress if you so desire. Position Your Design: Take your time to line up your transfer in the desired location on your item. Normally, there is no need to use heat-resistant tape on flat heat presses to keep your design in place, however it is highly recommended when pressing transfers onto hats or when using an iron to keep the transfer in place. You’ll get a feel for when this is needed. Press 1: Place a Parchment paper on top of the design & Press your transfer with Med to Heavy pressure at 310°F / 155°C for 30-35seconds. You cannot damage the transfer by pressing with more heat, pressure, or time — within reason. However, too much heat can damage your garment, so test first and use parchment paper or a protective guard sheet to protect your garment from a direct iron. Press 2: Let  Sit for 10 Seconds and Repeat press Let It Cool. Then Peel It: After pressing, let your transfer rest until it is cool to the touch (minimum of 15-30 seconds). Once cool, lift the transfer from one corner and gently peel back. Don’t use your hands, use your EYES. This ensures every piece of your design is adhering to your item. If not, stop peeling, lay it back down, and trouble shoot as follows — (1.) If some or all of the design does not transfer AND it was cool when peeling, it means there was not enough heat, pressure, or time. Press your transfer again with more pressure and time first (+5-10 seconds). (2.) If that doesn’t work, try 15°F heat increments until you find the sweet spot. You truly cannot damage the transfer by pressing multiple times. Final Press & Wash Instructions: Place a parchment paper or a single layer of t-shirt material over the design and press again for 15 seconds to soften the design, increase durability, and remove shine. If you want a shiny finish, cover with a protective guard sheet for the final press. When washing, flip shirt inside out, wash on cold and dry using low heat or hang. *By purchasing you agree that the process for the application of our transfers is your responsibility and we not refund due to user error. There is a learning curve to heat pressing and transfers and every heat press is different.**A heat press is recommended though this will work with a circut or an iron as well***All Sales are Final

YOU WILL RECEIVE TONS OF COMPLIMENTS: Prepare for a flood of compliments! Each design is a fantastic conversation starter, and everyone will be curious about where you got it. Print Size: Pressing Instructions:  Pre-Press: Removing moisture is unnecessary but recommended. Only do a prepress if you so desire. Position Your Design: Take your time to line up your transfer in the desired location on your item. Normally, there is no need to use heat-resistant tape on flat heat presses to keep your design in place, however it is highly recommended when pressing transfers onto hats or when using an iron to keep the transfer in place. You’ll get a feel for when this is needed. Press 1: Place a Parchment paper on top of the design & Press your transfer with Med to Heavy pressure at 310°F / 155°C for 30-35seconds. You cannot damage the transfer by pressing with more heat, pressure, or time — within reason. However, too much heat can damage your garment, so test first and use parchment paper or a protective guard sheet to protect your garment from a direct iron. Press 2: Let  Sit for 10 Seconds and Repeat press Let It Cool. Then Peel It: After pressing, let your transfer rest until it is cool to the touch (minimum of 15-30 seconds). Once cool, lift the transfer from one corner and gently peel back. Don’t use your hands, use your EYES. This ensures every piece of your design is adhering to your item. If not, stop peeling, lay it back down, and trouble shoot as follows — (1.) If some or all of the design does not transfer AND it was cool when peeling, it means there was not enough heat, pressure, or time. Press your transfer again with more pressure and time first (+5-10 seconds). (2.) If that doesn’t work, try 15°F heat increments until you find the sweet spot. You truly cannot damage the transfer by pressing multiple times. Final Press & Wash Instructions: Place a parchment paper or a single layer of t-shirt material over the design and press again for 15 seconds to soften the design, increase durability, and remove shine. If you want a shiny finish, cover with a protective guard sheet for the final press. When washing, flip shirt inside out, wash on cold and dry using low heat or hang. *By purchasing you agree that the process for the application of our transfers is your responsibility and we not refund due to user error. There is a learning curve to heat pressing and transfers and every heat press is different.**A heat press is recommended though this will work with a circut or an iron as well***All Sales are Final